how u polish rims?????

[jdmkain1706]

Wats gd ctv jus wanna know how u polish rims does any 1 know??????

[chagy87]

Hit up lsdb1 he might tell you his secreats

[jdmkain1706]

Hit up lsdb1 he might tell you his secreats

I know right looks like he's da best at polishing rims I seen da pics of hondaman203s swirlies them shyts came out sexy

[BB DC294 NHCT]

thats alot of time to do that.

[jdmkain1706]

Ill take my time and do it

[91EscortGT]

idk, LSDB1 is a beast!
I dropped my rims off saturday night around 6pm, they were done @ 8AM sunday my rims dont have a whole lot of surface area bcuz of the paint, but still hes a beast!

[HonDaMaN203]

bump lsdb1 mann he a beast 4real u seen my bladez idk if yall like but they came out freshhhhhhhhhhhhhh

[JDM_DC5]

pm'd u a link

[lsdb1]

THIS IS FROM A STICKY ON HONDA-TECH....everything you need to know is in here

Taken from a quick writeup i did on a local forum.. questions, comments, editing welcome. A side project i started in the middle of winter and finally finished. takes about 4-5 hours/rim. took way longer than i expected but once i started i couldnt turn back. anyway.. here's what i wrote.

----------

The person i baught my SiR rims off of didn't take very good care of them. Drove them in the winter and they seen their fair bit of salt. Clear coat is chipping off and there is some pitting.. and for some dumb-ass reason Honda decided to put the wheel weights on the outside of these rims leaving nasty marks when you change and rebalance your tires..

So now i'm left with the job of trying to make them look new again.

Things you'll need.

Gloves - buy a 100 pack at the drug store, if you dont use gloves get ready to have black hands for a week.
Sandpaper 150*, 220, 320, 400, 600, 800, 1500
2 cans of mothers polish
6" Buffer
Small palm sander
A few rolls of that blue paper towel stuff from canadian tire..


* Be carefull with 150 grit..use only to sand down curb scrapes or really bad areas.. you'll need to speed 3 x time with 220 grit to get rid of the sanding marks that the 150 will leave behined.

Step 1: strip rims with heavy duty paint stripper - follow the instructions exactly, do not do it on a humid or cold day or expect to do it agian!

SKIP TO STEP 4-8 if rims are smooth after stripping - use your own judgement. Sir rims and many other OEM rims have concentric machined rings that need to be sanded off so you need to start off with 220 grit

Step 2: Sand down with 220 BY HAND use a wood block for flat parts. take your time and make sure you dont see anything but the sanding marks that the 220 will leave behined. I sand dry with 220. this step will take the most time! do a good job.

Step 3:

Use 320 with the palm sander along with lots of water.
Palm sand as much as the rim as you can but be carefull not to let the sanders lip hit anything! let the sander to the sanding and use lots of water.

clean with clean rags and water.

hand sand areas you cant get at with the palm sander

sand again with the palm sander and fresh sand paper.

Step 4: (same as step 3 with 400 grit)
Step 5: (same as step 3 with 600 grit)

Step 6: Hand sand with 800 grit - take your time and get everything! I used this maroon colored paper from home hardware - it didn't last long using lots of water but it worked so well. buy 4 sheets of this stuff! Thumb Up I did 2 good passes with this stuff.

Step 7: Do the same with 1500 grit. the rim will look very smooth and very DULL. if it looks even and dull than you did a good job.

Step 8: Smear a decent amount of mothers on the whole rim. WITH A NEW CLEAN bonnet buff until you start to see circles/haze - you'll see the rim start to get very shiney but will leave a buffing patteren. keep doing this but dont let it get competely dry.. hard to explain but you cant really screw anything up at this point, just might have to do it over. turn the bonnet inside out for the next 'step 8' that you do.

Step 9: WITH A NEW CLEAN bonnet buff the rim. If you did the buffing part right the rim will look like a mirror in seconds. if it still looks hazy than keep experimenting with step 8. you will surprise yourself

[jdmkain1706]

idk, LSDB1 is a beast!
I dropped my rims off saturday night around 6pm, they were done @ 8AM sunday my rims dont have a whole lot of surface area bcuz of the paint, but still hes a beast!

They still look good bro keep them up

[jdmkain1706]

bump lsdb1 mann he a beast 4real u seen my bladez idk if yall like but they came out freshhhhhhhhhhhhhh

Hell yea I like dem shyts jus lookin at them makes me wanna lick them lmao don't try 2 trade those bro u should keep them

[single slam 12]

dudes cool and gets work done he even gave you instructions but you will end up taking it to him in the end. fuk that i'll pay too much s h i t involved better off paying.

[lsdb1]

dudes cool and gets work done he even gave you instructions but you will end up taking it to him in the end. fuk that i'll pay too much s h i t involved better off paying.

hahah....thanks my nigga

[jdmkain1706]

dudes cool and gets work done he even gave you instructions but you will end up taking it to him in the end. fuk that i'll pay too much s h i t involved better off paying.

Yea but I wanna try it myself first then if it don't come out right then ill get somebody 2 do it dats how u learn how 2 do shyt ,dats how I learned how 2 work on cars and shyt