swap help

[2000si...]

http://www.jdmenginescorp.com/engine_details/acura_acura-integra-jdm-b18b-obd2-dohc-engine-96-00-motor-1.8-liter-5spd-trans-ecu

just bought this obd2 ls with tranny and ecu. im dropping it into a 99 ek d16y7 what else do i need.

[97EKHATCH]

Mounts and em1 rear t bracket and linkage etc cause I'm doing the same in my ek

[EJ8-Type R]

Axles. Half shaft. Linkage. 99-00 si t bracket. Use ur mounts, b series or aftermarket. Upper and lower radiator hoses

Also will be doing a b series swap in my ek lol

[93eg2sol]

Axles. Half shaft. Linkage. 99-00 si t bracket. Use ur mounts, b series or aftermarket. Upper and lower radiator hoses

Also will be doing a b series swap in my ek lol

If I'm not mistaken u have to buy aftermarket mounts with eks... U can't use Ur stock ones..

[EJ8-Type R]

If I'm not mistaken u have to buy aftermarket mounts with eks... U can't use Ur stock ones..

Idk that's what I was told but I brought hasport mounts for my swap anyways lol

[96ekdx]

you will need
SI rear T bracket
SI post mount that goes onto the block next to the timing belt
axles
you can either get a 99-00 ex harness for alot less modifications to or use your stock harness and rewire
99-00 SI shiftlinkage
and of course the whole swap it self

[leo2006leo]

you will need
SI rear T bracket
SI post mount that goes onto the block next to the timing belt
axles
you can either get a 99-00 ex harness for alot less modifications to or use your stock harness and rewire
99-00 SI shiftlinkage
and of course the whole swap it self

Ex harness for a ls?

Use your regular harness

B series shift linkage

3 post mount
Rear t bracket

[93eg2sol]

Ex harness for a ls?

Use your regular harness

B series shift linkage

3 post mount
Rear t bracket

Ex harness .. I was thinkin the same...

[H22SteakSauce]

Ex harness for a ls?

Use your regular harness

B series shift linkage

3 post mount
Rear t bracket

You need an ex harness if your not gonna rewire it. Y7 uses a 3 wire iac similar to a k20. I've seen the cars you swap, I wouldn't listen to your instructions on how to tie shoes.

[leo2006leo]

You need an ex harness if your not gonna rewire it. Y7 uses a 3 wire iac similar to a k20. I've seen the cars you swap, I wouldn't listen to your instructions on how to tie shoes.

Lol I've never heard of that in my life

[leo2006leo]

Witch one of my cars you saw :D

[H22SteakSauce]

Witch one of my cars you saw :D

Some ls Vtec coupe u had

[leo2006leo]

When it was broken? When it was gsr no cel light bucko

[96ekdx]

yes a ex harness you just won't use the vtec plug and pressure switch plug...and you have to extend one plug that goes on the intake mani and also the o2 sensor too...i'll look it out and write it down i forget whichs ones

[96ekdx]

okay...
change CKF sensor(change the cranks sensor located next to the crank to a b series one)
wire in secondary o2 sensor cause its run in the cabin of ur ek
extend primary o2 sensor


Also my boi had a jdm b20 and it didn't come with a crank sensor if thus shall happen you can use the CKF bypass trick that i use...here is the link...

http://www.ff-squad.com/technet/ckftrick.htm