b16 crank endplay

[chagy87]

prob the washers he prob forgot to put them back in hopefully is just that
btw i talked to nick about the 6 puck he does not want to get rid of it at this very moment

[doitpropa]

prob the washers he prob forgot to put them back in hopefully is just that
btw i talked to nick about the 6 puck he does not want to get rid of it at this very moment

thank you but i got my clutch re padded or w.e. its called

[doitpropa]

could teh play b that there is no tranny bolted to it to put pressure on the crank? there was thrust wahsers in there nd i swapped umm out ne ways nd theres still the play its like not enough to c but enough to hear ... insight plz...... jus don't wanna do ne thing wrong been puttin this together for far to long

[CTgoldhatch]

it is hard to say i know there some be some play if you look in a service book it will tell you how much play there sould be crank end play. if you put new washers drop it in and fire it up not to much more you can do. the tranny being bolted up to it dont make it any more or any less play

[doitpropa]

i think the shaft hittin the flywheel woudl delete the play but not exactly sure ... like u said best i can do is drop it in nd fire it up .... hope to god i can give tucoman a+ in bad/good seller lol i think it'll b fine now that i no it has the washers will update hopefully tomorrow w/ it running ... if only i hadda garage i'd drop it in tonite .... thinkin bout getin it in w/ sum droplites 4 a little though

[doitpropa]

it is hard to say i know there some be some play if you look in a service book it will tell you how much play there sould be crank end play. if you put new washers drop it in and fire it up not to much more you can do. the tranny being bolted up to it dont make it any more or any less play

on the contrary it did make a difference ... no play at all in crank now that tranny is bolted to it it started just need a few more bolts nd it should b good 2 go

[LILRED_TURBO]

that block should not have any end play is not a DSM when its all back together if u have a high rated pressure plate your only going to ************ it up more. You need new thrust washers that GO TO THAT BLOCK not just any old b motor thrust washers. After buying new ones read your Haynes manual you have to check for certain clearances. like I said it shouldn’t have any end play the transmission is holding pressure on the crank at the moment and that’s why u seem to think it took end play away but once you put your foot to that clutch and start up your going to thro you bottom end off balance.

I only heard of a Honda crankwalk one other time and it was about 1/4 inch side to side now that’s bad.

[doitpropa]

that block should not have any end play is not a DSM when its all back together if u have a high rated pressure plate your only going to ************ it up more. You need new thrust washers that GO TO THAT BLOCK not just any old b motor thrust washers. After buying new ones read your Haynes manual you have to check for certain clearances. like I said it shouldn’t have any end play the transmission is holding pressure on the crank at the moment and that’s why u seem to think it took end play away but once you put your foot to that clutch and start up your going to thro you bottom end off balance.

I only heard of a Honda crankwalk one other time and it was about 1/4 inch side to side now that’s bad.

well i really dont' havva choice but to run it nd i guess i'ma jus start lookin 4 a new block but it should b fine i mean u coulnt' see the play just here it so idk man nd they are new thrust washers in there

[LILRED_TURBO]

try it out

[doitpropa]

update :::: so everyone that said there should b no play was rite because now that i changed the bearings nd thrust washer torqued everything properly there is no movement in the crank ... and the machinist i brought the crank to for polishing said it looked like there was 276k miles on it not 76k like the guy i bought it from stated